Important notice: We are currently having issues with incoming calls, where the caller cannot hear us. In these instances we will call back. We are working to get the issue fixed. In the meantime please email [email protected] for any enquiries.
OMAL
The new and updated Omal aluminium standard spring return pneumatic actuator - now with an integrated NAMUR interface and adjustable end of travel stops - from SRN15 and bigger, to 4000Nm.
Torque output from 15Nm to 4000Nm. Torque: the return torque depends on spring action only not withstanding the air supply. The spring is provided in four different sizes.
Mounting flange according to EN ISO 5211. ISO: F03 - F04 - F05 - F07 - F10 - F12 - F14 - F16 - F25.
Energized and self-lubricated strips. Less friction between piston and cylinder. It prevents the bonding of the seal to the cylinder even after long periods of inactivity.
Slots, bushes and pins made by steel with hardness higher than 50 HRC. Higher resistance to the forces inside the actuator. Rolling friction between piston and slot also mean less friction with consequently less wear on the relevant parts.
Scotch yoke design (transforming rotary motion into linear motion using piston and shaft without teeths/gears). Smaller volume/size and less weight than rack and pinion actuators (with the same torque) therefore less space required for installation and consequent savings on the construction sizing of the plant/equipment. Lower air consumption compared to the rack and pinion actuators (-40% air cm3/Nm for Double Acting and -20% air cm3/Nm for Spring Return) therefore less load on the compressor or the possibility of using a smaller compressor's size.
Rolled cylinder. Less wear of the energized ties thanks to the low roughness of the surface (0.15 micron Ra).
In accordance with EN 15714-3
Rotation angle 92° (-1°, +91°C)
ATEX version in conformity with directive 2014/34/EU - Available on request
SIL 3 Certified
Temperature: from 0°C to +80°C; from -20°C to +80°C with dry air only. (High Temperature -20°C, +150°C ; Low Temperature -50°C, +60°C special execution)
Air supply: 5,6 bar; maximum 8,4 bar
Actuating media: filtered dry compressed air, not necessarily lubricated. In case of lubricated air, either non detergent oil or NBR compatible oil, must be used.
OMAL spring return pneumatic actuator, namur interface - Part numbers coming soon, contact us for more information
Art:
The new and updated Omal aluminium standard spring return pneumatic actuator - now with an integrated NAMUR interface and adjustable end of travel stops - from SRN15 and bigger, to 4000Nm.
Torque output from 15Nm to 4000Nm. Torque: the return torque depends on spring action only not withstanding the air supply. The spring is provided in four different sizes.
Mounting flange according to EN ISO 5211. ISO: F03 - F04 - F05 - F07 - F10 - F12 - F14 - F16 - F25.
Energized and self-lubricated strips. Less friction between piston and cylinder. It prevents the bonding of the seal to the cylinder even after long periods of inactivity.
Slots, bushes and pins made by steel with hardness higher than 50 HRC. Higher resistance to the forces inside the actuator. Rolling friction between piston and slot also mean less friction with consequently less wear on the relevant parts.
Scotch yoke design (transforming rotary motion into linear motion using piston and shaft without teeths/gears). Smaller volume/size and less weight than rack and pinion actuators (with the same torque) therefore less space required for installation and consequent savings on the construction sizing of the plant/equipment. Lower air consumption compared to the rack and pinion actuators (-40% air cm3/Nm for Double Acting and -20% air cm3/Nm for Spring Return) therefore less load on the compressor or the possibility of using a smaller compressor's size.
Rolled cylinder. Less wear of the energized ties thanks to the low roughness of the surface (0.15 micron Ra).
In accordance with EN 15714-3
Rotation angle 92° (-1°, +91°C)
ATEX version in conformity with directive 2014/34/EU - Available on request
SIL 3 Certified
Temperature: from 0°C to +80°C; from -20°C to +80°C with dry air only. (High Temperature -20°C, +150°C ; Low Temperature -50°C, +60°C special execution)
Air supply: 5,6 bar; maximum 8,4 bar
Actuating media: filtered dry compressed air, not necessarily lubricated. In case of lubricated air, either non detergent oil or NBR compatible oil, must be used.
Please refer to the datasheet under 'downloads' for part numbers and/or technical data, we are working on getting all part numbers and technical data on the website as soon as possible.
OEM Automatics water and wastewater application specialists have gathered all our solutions in one place. Our products are used in everything from small municipal water works to larger regional plants.
Whether you’re pumping water, chocolate, oil or peanut butter knowing the product’s viscosity is essential to selecting the right pump. Find out more about viscosity and which pump may be suitable for your application!
Whether you're looking to upgrade your current solution or secure a more robust float switch for your next project, Taurus delivers performance you can count on.
When choosing between a pressure switch and a pressure sensor, the key lies in understanding your application. Our Pressure Monitoring experts breaks down the two devices for you.
Pumps are now officially part of our product offering! As we build our pump portfolio, we’re proud to announce that we are an official distributor of SAMOA Industrial, a well-established name in the fluid handling industry.
OEM Automatic's barcode scanner experts have broken down barcode technology to help you choose the right scanner for your application!
