PULS

PISA-M

The Pulse PISA-M electronic fuse is a 4-channel DIN rail-mountable fuse for 12 and 24 V DC systems. It is physically very small and builds only 22.5 mm in width on the DIN rail. PISA-M is very universal and power supplies from 90-480 W (24 V DC) can be used in front of it.
  • 4 channels (4x1-8A)
  • Only 22.5mm width
  • Joint or individual alarm
  • Fast or slow characterization

Selected variant

Art:

Selected variant

Technical data

Input data

Input voltage dc min 9,6 V DC
Input voltage dc max 30 V DC

Output data

Output current max 20 A
Output current per channel Channel 1-4 :1, 2, 3, 4, 6, 8 A

Efficiency / Lifetime / MTBF

Efficiency 98 %
Life span 268 000 h 4x5 A 40 C
MTBF (IEC 61709) 1 142 000 h 4x5 A 40 C

Dimensions

Width 23 mm
Height 104 mm
Depth 98 mm
Weight 0,1 kg

Other

Approvals CE
IP class IP20
Clamp type Push in
Cable size stranded max 2,5 mm²
Material protection Plastic
Voltage drop over semiconductor 130 mV
Back-feeding loads 30 V DC
Input connector Push-In
Output connectors Push-In

Product description

- 4 channels

- Only 22.5mm wide

- Each channel can be adjusted to: 1/2/3/4/6/8 A (max 20 A total)

- You can choose fast or slow characteristics (e.g. slow for equipment that requires starting current)

- Press connection

- Local or remote recovery

 

The courses can be turned on and off using the 4 buttons on the front. The track is on if it lights up green and off if it glows red with a steady light.

 

The 4 courses start at about 100 ms intervals.

The factory settings are that all channels are connected with the setting 1A and fast characteristic.

 

If a channel is tripped, the respective LED flashes red once for overload or short circuit and red twice for (a) the total overload protection of 20 A for sec is activated or (b) the power supply protection mode is activated. For more information, see the User's Guide, Section 9. To reset the course, press and hold the respective course button for 1 sec.

 

To check what the different channels are set to in the Amp level:

 

Press buttons 1 and 4 at the same time for a short time (50 ms).

 

LED 1 will then flash green quickly for the number of Amps set (once for 1 A, twice for 2 A, etc.).

 

To change the different Amp levels on the different channels: (Max. 20 A total)

Press buttons 1 and 4 at the same time for 1 sec (all channels will be orange)

 

Short press button 1 (50 ms), then press within 4 sec. the number of times corresponding to the desired gain level, e.g. 3 times corresponds to 3 A. Then it flashes quickly 3 times (green) (in 2 sequences) Then press button 1 for 1 sec. to save. It then shines with a solid green light. Repeat for channels 2-3 and 4. To exit the programming mode, press buttons 1 and 4 at the same time for a short time (50 ms).

 

To see and change whether the fuse is set to fast or slow characterization:

Press buttons 1 and 3 at the same time for a short time (50 ms)

 

LEDs 1-4 will then flash green at a fast speed for fast or slow characteristics (daytime running lights)

 

Press buttons 1 and 3 again at the same time for a short time (50 ms) (within 4 sec). This changes the characteristic.

 

This is automatically saved.

 

If you do not press any button within 10 seconds, you will automatically exit programming mode.

 

Clear recovery

If a circuit has tripped, you can apply a voltage of 10-30 V DC (under 1 sec) to terminals 3.3 (+) and 3.4 (-), once the cause has been found and the fault has been fixed. Other channels are not affected, regardless of whether they are connected or disconnected.

 

Alarm contact From the factory, it is delivered as a trippy alarm. See the 4 different alarm options below. For more information, see Section 12 of the User's Guide.

 

You can connect multiple PISA-M modules in parallel to create multiple courses. Each (+) on the PISA-M module must be connected directly to the power supply.

 

We recommend a free space of 40 mm above and 30 mm below. 0 mm on the sides, 15 mm if the component on the side emits heat (e.g. power supply).

 

Properties: (otherwise see section 6 of the data sheet)

Sensitivity: < 2ms - 0.22 sec in case of short circuit and 1.5 x In.

Slow: < 10 ms - 1.1 sec in case of short circuit and 1.5 x In.

Accessories

Contact us

If you need any help, you can contact us in one of the following ways:

phone 0116 284 9900

Send an e-mail Send an e-mail

comments Use live chat

Logo

Cookie settings for OEM.CO.UK

Cookies help us improve your experience with us, so in order to be able to handle login information, offer you personalised content and for basic functionality of this website, we use some cookies.

We will never sell on any information about you. 

You can accept all cookies or personalise your cookies preferences, you can also change your cookie preferences at any time by visiting our contact page.

Necessary Cookies

These cookies are necessary for the website to work and can not be turned off in our systems. They are usually used only in response to actions you have taken in connection with a service request, for example when setting personal preferences, logging in or filling out a form.

Analysis and measurement cookies

These cookies allow us to count the number of visits and traffic sources so that we can measure and improve our website performance. They help us know which pages are more or less popular and how visitors navigate around the site. The information that these cookies collect is aggregated and therefore completely anonymous. If you do not allow these cookies, we do not know when you have visited our website.

Marketing cookies

These cookies can be added by our partners. They can use them to create a profile of you, based on your interests, to show you more relevant information. They do not store any personal information - only information about your browser and device. If you do not accept these cookies, you will have a more general and less customized user experience.