Important notice - We will be performing system maintenance from 4pm Friday 19th April. Whilst we are performing this maintenance there will be no pricing available or ability to place orders. This will last for 2-3 days. Please contact customer support for any enquiries 0116 284 9900. We apologise for any inconvenience caused.
ELECTROMEN
EM-241 is a full bridge DC-motor starter. It is designed to work with DC-motor in applications where some special functions are needed.
Starter has adjustable acceleration and deceleration ramps, which make possible the smooth starts and stops. Adjustable current limit
protects motor against overcurrent and it can also be used as an end-stop. This device has also two settable speeds, which are usefull
in positioning applications. Control inputs FW and BW start the forward and backward run. STOP is for the motor shut-down. In -PLI
version there are also PULSE COUNTER which can be used for end limit use. This counter value keep in memory of card also when
power is turned off. SPEED-2 input activates preset speed-2, but it can also be used as input for analog speed control signal 0-5V.
FAULT terminal has at the same time input and output function, the pin is normally high, but is pulled down in overheat and
conditionally also in current trip situation. If FAULT-line is pulled down externally it will cause a stop and prevent the new start.
For example, it is possible to link fault pins of several units together and achieve a syncronous stop.
There are two selectable control modes, continuous and impulse. In continuous mode the motor runs as long as the control is active.
In impulse mode a short comand starts the motor, and only a new impulse will change the status. There is also few special settings
start-kick and auto reverse. The card has selectable input logics. Inputs are divided in two groups, control and limit -inputs. Groups can be individually set for NPN or PNP logic. The parameters are set with EM-236 interface unit. Operation of the controller and some of its
functional values can also be monitored with EM-236 interface unit.
FEATURES:
- small size
- high current output
- 2ch pulse counter inputs
- Pulse counter limits.
- current limit
- zero current limit
- overvoltage brake
- speed setting
- PWM 2 or 16 kHz
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- dip switch only in PCB. version B
- A softwares compatible for B ver. PCB.
- digital parameter setting
* Continuous current output when ambient temp is <50°C )
15A at 100% speed / 10A at 5-99% speed pwm=2kHz
10A at 100% speed / 5A at 5-99% speed pwm=16kHz
Peak ( 5s.) 30A at 2khz pwm and 25A at 16kHz pwm
| Analogue input | 0-5V |
|---|---|
| Control type | Speed, Direction, Torque, Soft start / stop |
| Current setting range | 0.1-20 A |
| Dimensions length x width x height | 72x42x25mm mm |
| Logic input high | >4V = ON |
| Logic input low | <1V = OFF |
| Max continuous current | *15 A |
| Mounting | DIN rail |
| Operating temperature | -40°C...+60°C |
|---|---|
| Peak current | 30 A |
| PWM frequency | 2kHz/16kHz |
| Suitable engine | DC |
| Supplier | Electromen |
| Supply voltage | 12 V DC, 24 V DC |
| Weight | 75 g |
EM-241 is a full bridge DC-motor starter. It is designed to work with DC-motor in applications where some special functions are needed.
Starter has adjustable acceleration and deceleration ramps, which make possible the smooth starts and stops. Adjustable current limit
protects motor against overcurrent and it can also be used as an end-stop. This device has also two settable speeds, which are usefull
in positioning applications. Control inputs FW and BW start the forward and backward run. STOP is for the motor shut-down. In -PLI
version there are also PULSE COUNTER which can be used for end limit use. This counter value keep in memory of card also when
power is turned off. SPEED-2 input activates preset speed-2, but it can also be used as input for analog speed control signal 0-5V.
FAULT terminal has at the same time input and output function, the pin is normally high, but is pulled down in overheat and
conditionally also in current trip situation. If FAULT-line is pulled down externally it will cause a stop and prevent the new start.
For example, it is possible to link fault pins of several units together and achieve a syncronous stop.
There are two selectable control modes, continuous and impulse. In continuous mode the motor runs as long as the control is active.
In impulse mode a short comand starts the motor, and only a new impulse will change the status. There is also few special settings
start-kick and auto reverse. The card has selectable input logics. Inputs are divided in two groups, control and limit -inputs. Groups can be individually set for NPN or PNP logic. The parameters are set with EM-236 interface unit. Operation of the controller and some of its
functional values can also be monitored with EM-236 interface unit.
FEATURES:
- small size
- high current output
- 2ch pulse counter inputs
- Pulse counter limits.
- current limit
- zero current limit
- overvoltage brake
- speed setting
- PWM 2 or 16 kHz
- flexible control inputs
- impulse / continuous mode
- rail base mountable
- dip switch only in PCB. version B
- A softwares compatible for B ver. PCB.
- digital parameter setting
* Continuous current output when ambient temp is <50°C )
15A at 100% speed / 10A at 5-99% speed pwm=2kHz
10A at 100% speed / 5A at 5-99% speed pwm=16kHz
Peak ( 5s.) 30A at 2khz pwm and 25A at 16kHz pwm
At OEM Automatic, we can supply a series of components for your one project. All under one roof. This case study discusses how we supplied several components for our customer's new electro-pneumatic control box.
Technosoft specialise in developing intelligent drives and certainly live up to the term 'intelligent’, by combining a powerful motor and motion controller to implement complex movements.
One of the leading names in motors and drives, Oriental Motor, has signed a distribution deal with OEM Automatic. OEM Automatic can support customers, especially where an AC or Brushless DC (BLDC) motor has been discontinued or proving hard to source.
The Simplex Motion integrated servomotor is a brushless DC motor with integrated electronics and outrunner rotor. You can now browse Simplex Motion servomotors on our website.
OEM Automatic currently offers PMW’s range of standard pancake motors, as well as its bespoke design service. PMW’s motor portfolio caters for customers requiring both brushed and brushless configurations, supplied as housed or frameless, for both geared and direct drive applications.
DOGA’s new 311 and 311E is a right angle geared motor range, available with or without an integrated drive offering CANopen compatibility,
|
|
|
|
|
|
||
|---|---|---|---|---|---|---|
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
| Parts | Price | ||
|---|---|---|---|
|
DC motor drive 12-24 V dc, 15 A, pulse counts for end limits
Art:
EM-241B-PLI
Copied
|
|
Select a variant in the list
If you need any help, you can contact us in one of the following ways:
