PULS

Power supply 1-phase, 24 V dc Dimension Q series, 40A

Pulse Dimension Q is a series power supply with very high performance. The efficiency is high over a wide load range, which results in reduced power consumption and longer life regardless of load current. An average efficiency is 93.8% with a peak value of 94.6%. The power loss at idle is only 12 W.

The bonus power provides 50% extra reserve with retained 24 V dc (60 A) which is an advantage when connected loads have high starting currents and to bridge temporary current peaks. The bonus power is limited to 4 seconds to avoid constant overloading of the power supply and wiring. In addition to the bonus effect leave the unit a very high short-circuit current (for a number of milliseconds) that helps to secondary fuses. If the overload remains after 4 sec. Ports end in the so called, hiccup mode. When the output voltage drops below 21 V dc shut the unit by the end of the 18's. And then make a new start attempt. If the overload / short connection is gone restarts the power supply automatically. If the overload / short circuit persists, the unit output current of approx. 2 sec and then again turn off.

Heavy transient ensure operation also in very störrik electrical environment and also has QS40.244 active inrush current protection, which means a very low starting current, even if the unit has been in operation for a longer time. Especially useful for redundant / parallel-connected systems.

Simple diagnostics via DC-OK relay that falls on the output voltage deviates more than 10% from the set value, a green LED indicates DC-OK, the red LED indicates overload.
The unit can also be remote controlled for on / off function, three different connection options available. Can be used instead of expensive DC contactors when you need to break up the 24 VDC side. Note. remote control function has no safety circuit and therefore should not be used in the security context.
Active PFC reduces power consumption and harmonics close to zero. Moreover, the current distribution in the phases were much more even at the voltage asymmetry.

 

Output characteristics

Remote function

Bonus power

The power supply has bonus power that enables high power extraction with retained 24 V dc for 4 seconds, which is a major advantage when connected loads have high starting currents, for example. engines. How often you can use the bonus effect depends on the application. With the below chart and formula estimated the repeat time available for each individual application. The bonus power is available as soon as the power supply is started and after a short circuit

 

Bonus power

Work cycle

Bonus power

Operating characteristics

Po

Nominal load current

Ppeak

Peak current

To

Time between bonus effect

Tpeak

Peak current time

Work cycle

Tpeak/(Tpeak+To)

To=

Tpeak-(duty cycle)*Tpeak)/work cycle

Ex. Peak current (Ppeak) 50 A = 125%. Peak time is 3 seconds. Nominal load current (Po) is 30 A. 30 A = 75% of In. According to the diagram, the working cycle about 0.45. To = 3 - (0.45 * 3) / 0.45 = 3.6. Maximum repeat time of bonus power is 3.6 seconds.

 

 

Indicators

Indicators

Overload
LED

DC-OK
LED

DC-OK
contact

Normal operation

Off

On

Closed

During bonus poweroutput

Off

On

Closed

Overload (Hick-up)

Flashing

Off

Open

Short circuit

Flashing

Off

Open

Over temperature

Flashing

Off

Open

Remote shutdown

Flashing

Off

Open

No input voltage

Off

Off

Open

Ex. Peak current (Ppeak) 50 A = 125%. Peak time is 3 seconds. Nominal load current (Po) is 30 A. 30 A = 75% of In. According to the diagram, the working cycle about 0.45. To = 3 - (0.45 * 3) / 0.45 = 3.6. Maximum repeat time of bonus power is 3.6 seconds.

 

Read more
  • Output current 40 A
  • Up to 94.6% efficiency
  • High short-circuit currents
  • Remote function
  • Protective filters

Selected variant

Selected variant

Technical data

Input data

Input voltage ac 100-240 V
Input voltage ac min 90 V AC
Input voltage ac max 264 V AC
Inrush current at 120 V ac typical 17 A
Inrush current at 230 V ac typical 11 A
Input voltage range Wide-range
Power factor at 120 V ac, full load. Typical 0,99
Power factor at 230 V ac, full load. Typical 0,99
Number of phases 1

Output data

Output voltage 24 V DC
Output voltage min 24 V DC
Output voltage max 28 V DC
Output current 40 A
Power 960 W

Efficiency / Lifetime / MTBF

Efficiency at 120 V ac, full load, typical 93,6 %
Efficiency at 230 V ac, typical 93,9 %
Efficiency at 230 V ac, full load, typical 94,6 %
Lifetime at 120 V ac, full load and +40 ° C 64000 h
Lifetime at 230 V ac, full load and +40 ° C 84000 h
MTBF (IEC 61709) 230 V ac, max load, 40 ° C 300000 h

Dimensions

Width 125 mm

*Invisible Heading*

Height 124 mm
Depth 127 mm
Weight 1,9 kg

Other

Approvals ABS, ATEX, CB, CE, CSA, GL, IECEx, UL
Hold time at 120 V ac, typical full load 27 ms
Hold time at 230 V ac, typical full load 27 ms
IP class IP20
Clamp type Spring-clamp
Material protection Aluminium
Supply frequency 50-60 Hz +-6%
Ripple max 100 mV pp
Series Dimension Q
Power consumption 120 V ac 8,6 A
Power consumption 230 V ac 4,5 A
Power drop from +60 °C to + 70 °C 24 W/°C
Temperature min without derating -25 °C
Temperature max without derating 60 °C
Type Power Supply AC-DC
DC relay output Yes

Product description

Pulse Dimension Q is a series power supply with very high performance. The efficiency is high over a wide load range, which results in reduced power consumption and longer life regardless of load current. An average efficiency is 93.8% with a peak value of 94.6%. The power loss at idle is only 12 W.

The bonus power provides 50% extra reserve with retained 24 V dc (60 A) which is an advantage when connected loads have high starting currents and to bridge temporary current peaks. The bonus power is limited to 4 seconds to avoid constant overloading of the power supply and wiring. In addition to the bonus effect leave the unit a very high short-circuit current (for a number of milliseconds) that helps to secondary fuses. If the overload remains after 4 sec. Ports end in the so called, hiccup mode. When the output voltage drops below 21 V dc shut the unit by the end of the 18's. And then make a new start attempt. If the overload / short connection is gone restarts the power supply automatically. If the overload / short circuit persists, the unit output current of approx. 2 sec and then again turn off.

Heavy transient ensure operation also in very störrik electrical environment and also has QS40.244 active inrush current protection, which means a very low starting current, even if the unit has been in operation for a longer time. Especially useful for redundant / parallel-connected systems.

Simple diagnostics via DC-OK relay that falls on the output voltage deviates more than 10% from the set value, a green LED indicates DC-OK, the red LED indicates overload.
The unit can also be remote controlled for on / off function, three different connection options available. Can be used instead of expensive DC contactors when you need to break up the 24 VDC side. Note. remote control function has no safety circuit and therefore should not be used in the security context.
Active PFC reduces power consumption and harmonics close to zero. Moreover, the current distribution in the phases were much more even at the voltage asymmetry.

 

Output characteristics

Remote function

Bonus power

The power supply has bonus power that enables high power extraction with retained 24 V dc for 4 seconds, which is a major advantage when connected loads have high starting currents, for example. engines. How often you can use the bonus effect depends on the application. With the below chart and formula estimated the repeat time available for each individual application. The bonus power is available as soon as the power supply is started and after a short circuit

 

Bonus power

Work cycle

Bonus power

Operating characteristics

Po

Nominal load current

Ppeak

Peak current

To

Time between bonus effect

Tpeak

Peak current time

Work cycle

Tpeak/(Tpeak+To)

To=

Tpeak-(duty cycle)*Tpeak)/work cycle

Ex. Peak current (Ppeak) 50 A = 125%. Peak time is 3 seconds. Nominal load current (Po) is 30 A. 30 A = 75% of In. According to the diagram, the working cycle about 0.45. To = 3 - (0.45 * 3) / 0.45 = 3.6. Maximum repeat time of bonus power is 3.6 seconds.

 

 

Indicators

Indicators

Overload
LED

DC-OK
LED

DC-OK
contact

Normal operation

Off

On

Closed

During bonus poweroutput

Off

On

Closed

Overload (Hick-up)

Flashing

Off

Open

Short circuit

Flashing

Off

Open

Over temperature

Flashing

Off

Open

Remote shutdown

Flashing

Off

Open

No input voltage

Off

Off

Open

Ex. Peak current (Ppeak) 50 A = 125%. Peak time is 3 seconds. Nominal load current (Po) is 30 A. 30 A = 75% of In. According to the diagram, the working cycle about 0.45. To = 3 - (0.45 * 3) / 0.45 = 3.6. Maximum repeat time of bonus power is 3.6 seconds.

 

Accessories

Related products

Related

automation components for specialist vehicles
Blog

Automation Components for Specialist Vehicles

The specialist vehicle industry can include automotive and EV, heavy vehicles such as agriculture and rail, and marine.  This email takes you through some of the various products we offer for specialist vehicle applications.

Wohner power distribution
Product news Blog

Modern Power Distribution

This blog post delves into the key components, current trends, and best practices in power distribution, illustrating the significant impact these systems have on our daily operations and long-term energy strategies.

Dehn lightning and surge protection
Product news Blog

Lightning and surge protection to safeguard equipment

We shine a spotlight on surge protection devices (SPDs), a crucial yet often overlooked component in industrial settings. Every surge of electricity, every fluctuation in voltage, poses a potential threat to your machinery and systems.

Klauke crimping stripping and punching tools
Product news

Efficient crimping, punching and stripping

Renowned for high-quality cable cutting and crimping tools, Klauke serves electrical contractors, cable jointers, and linemen across a spectrum of sectors

electro pneumatic control box customised bespoke solutions
Case studies

Case Study - Electro Pneumatic Control Box

At OEM Automatic, we can supply a series of components for your one project. All under one roof. This case study discusses how we supplied several components for our customer's new electro-pneumatic control box. 

Flexa e mobility cable protection, conduits and cable sleeves
Blog

Cable Protection For Emobility

To promote constant and reliable performance, as well as a longer life of parts in the vehicle, it is important to consider the right cable protector.

Parts Input voltage ac Input voltage ac min Inrush current at 120 V ac typical Inrush current at 230 V ac typical Input voltage range Power factor at 120 V ac, full load. Typical Power factor at 230 V ac, full load. Typical Efficiency at 120 V ac, full load, typical Efficiency at 230 V ac, typical Lifetime at 120 V ac, full load and +40 ° C Lifetime at 230 V ac, full load and +40 ° C MTBF (IEC 61709) 230 V ac, max load, 40 ° C Weight Approvals Hold time at 120 V ac, typical full load Hold time at 230 V ac, typical full load Supply frequency Power consumption 120 V ac Power consumption 230 V ac Price
100-240 V
90 V AC
17 A
11 A
Wide-range
0,99
0,99
93,6 %
93,9 %
64000 h
84000 h
300000 h
1,9 kg
ABS, ATEX, CB, CE, CSA, GL, IECEx, UL
27 ms
27 ms
50-60 Hz +-6%
8,6 A
4,5 A
200-240 V
170 V AC
14 A
0,96
93,8 %
59000 h
366000 h
1,8 kg
ABS, CB, CE, CSA, GL, UL
30 ms
50-60 ±6 %
4,6 A

Selected variant

Select a variant in the list

Contact us

If you need any help, you can contact us in one of the following ways:

phone 0116 284 9900

Send an e-mail Send an e-mail

comments Use live chat