PULS
24 V dc UPS for external battery 3.9-40 Ah
UB10.241 is suitable for use in applications in which interruptions occur relatively often and the times are fairly short, such as for assuring process conclusion and retaining operation of PLC and other critical components.
A complete DC-UPS system consists of a control unit and battery, and power supply with suitable power for the application. In the event of a power outage, the battery is automatically switched in and supplies the connected loads. The control unit requires just (1) 12 V battery that then transforms the battery voltage up to 22.3 V dc. Two batteries do not need to be matched with one another and the output voltage does not follow the battery's discharge curve but is instead constant at 22.3 V. The battery capacity is utilized 100 % compared with two batteries connected in series, where one of the batteries is not fully charged.
Two relay outputs indicate status; the module is ready (battery capacity >85 %) and the module is active. (buffer mode) The control unit tests the battery's condition in cycles. When it is time to replace the battery, a relay output is activated (replace battery). At the front, optimized final charging voltage in relation to ambient temperature is selected. There are three available alternatives: 10 °C, 25 °C and 40 °C.
The back-up time can be set in different time ranges to save battery capacity. When choosing constant discharge, the output voltage will be active until the battery reaches deep discharge and the control unit then disconnects the battery. There is also an input, Inhibit, for external shut-off of the back-up time. In the event of a battery fuse fault, the “ready” output is deactivated and a red LED lights on the control unit. The output is current limited and turns itself off after about 5 seconds after a short circuit to spare the battery and at the same time, avoids tripping the battery fuse. In the event of a short circuit in the battery mode, the module supplies about 20 A, which helps trip any secondary fuses.
Monitoring of the battery fuse and current limitation in the event of short circuits provides increased reliability and guarantees that the UPS will function after a short circuit. There is no galvanic isolation between the 24 V dc input and output or between 24 V and 12 V. Isolation between the mains and the output is executed via the power supply.
Backup times
Back-up time with 7 Ah battery (curve A) | Back-up time with 26 Ah battery |
|
|
- Load current 10 A
- Only one 12 V battery
- Optimized battery charging
- Optional backup times
- Relay outputs for status
Selected variant
Technical data
Input data |
|
|---|---|
| Input voltage from the unit | 24 V DC |
| Input voltage from the battery | 12 V DC |
| Input voltage for battery connection | 22,8 V DC |
| Input current during charging | 1,2 A |
Output data |
|
| Output current at 24 V dc | 10 A |
| Output voltage for battery operation | 22,25 |
| Output voltage normal operation | 24 V DC |
| Output voltage at buffering | 22,25 V DC |
| Output current for battery operation max | 10 A (15 A @ 5 s) |
| Output current during operation max | 15 A |
Efficiency / Lifetime / MTBF |
|
| Efficiency | 97,8 % |
| Life span | 137 400 h @ 10 A, 40 °C |
| MTBF (IEC 61709) | 886 000 h @ 10 A, 40 °C |
Dimensions |
|
| Width | 49 mm |
| Height | 124 mm |
*Invisible Heading* |
|
|---|---|
| Depth | 117 mm |
| Weight | 0,65 kg |
Other |
|
| Approvals | ABS, CB, CE, CSA, CSA US, EX, GL, IECEx, UL |
| IP class | IP20 |
| Charging the battery type | 1,5 A |
| Material protection | Aluminium |
| Ripple max | 20 mV pp |
| Voltage level for battery connection | 22,3 V DC |
| Power drop from +60 °C to + 70 °C | 9,6 W/°C |
| Temperature min without derating | -25 °C |
| Temperature max without derating | 60 °C |
| Permitted battery sizes | 3,9-40 Ah |
| Type Power Supply | DC-UPS |
Product description
UB10.241 is suitable for use in applications in which interruptions occur relatively often and the times are fairly short, such as for assuring process conclusion and retaining operation of PLC and other critical components.
A complete DC-UPS system consists of a control unit and battery, and power supply with suitable power for the application. In the event of a power outage, the battery is automatically switched in and supplies the connected loads. The control unit requires just (1) 12 V battery that then transforms the battery voltage up to 22.3 V dc. Two batteries do not need to be matched with one another and the output voltage does not follow the battery's discharge curve but is instead constant at 22.3 V. The battery capacity is utilized 100 % compared with two batteries connected in series, where one of the batteries is not fully charged.
Two relay outputs indicate status; the module is ready (battery capacity >85 %) and the module is active. (buffer mode) The control unit tests the battery's condition in cycles. When it is time to replace the battery, a relay output is activated (replace battery). At the front, optimized final charging voltage in relation to ambient temperature is selected. There are three available alternatives: 10 °C, 25 °C and 40 °C.
The back-up time can be set in different time ranges to save battery capacity. When choosing constant discharge, the output voltage will be active until the battery reaches deep discharge and the control unit then disconnects the battery. There is also an input, Inhibit, for external shut-off of the back-up time. In the event of a battery fuse fault, the “ready” output is deactivated and a red LED lights on the control unit. The output is current limited and turns itself off after about 5 seconds after a short circuit to spare the battery and at the same time, avoids tripping the battery fuse. In the event of a short circuit in the battery mode, the module supplies about 20 A, which helps trip any secondary fuses.
Monitoring of the battery fuse and current limitation in the event of short circuits provides increased reliability and guarantees that the UPS will function after a short circuit. There is no galvanic isolation between the 24 V dc input and output or between 24 V and 12 V. Isolation between the mains and the output is executed via the power supply.
Backup times
Back-up time with 7 Ah battery (curve A) | Back-up time with 26 Ah battery |
|
|
Related
Efficient crimping, punching and stripping
Renowned for high-quality cable cutting and crimping tools, Klauke serves electrical contractors, cable jointers, and linemen across a spectrum of sectors
Case Study - Electro Pneumatic Control Box
At OEM Automatic, we can supply a series of components for your one project. All under one roof. This case study discusses how we supplied several components for our customer's new electro-pneumatic control box.
Cable Protection For Emobility
To promote constant and reliable performance, as well as a longer life of parts in the vehicle, it is important to consider the right cable protector.
Switch disconnectors without compromise
We have now added switch disconnectors to our range! Switch disconnectors contribute to the overall functionality and safety of electrical systems.
Electronic Circuit Breaker - LoccBox
LOCC-Box from Lutze is an intelligent current monitoring device that provides reliable protection of DC circuits in a slimline 8.1mm housing.
The Push In Technology You Need at OEM Automatic
OEM Automatic has integrated push-in technology into it's product offering for many years now. In this blog post, we'll explore the various benefits of push-in technology and some of the products we offer that make use of this innovation, such as push-in terminals, push-in sockets, and even push-in heaters.
