MINIMOTOR
MOTOR: Brushless 4-pole three-phase sinusoidal motor, totally enclosed. Rotor with NdFeB magnets. Thermal cutoff. Winding Class F. Thermal cutoff. Protection IP65 in compliance with IEC/EN 60529 standards. Bearings with reduced backlash and special grease for high temperatures.
DRIVE: Power 24 and/or 48 Vdc • Magnetic absolute encoder SSI (12bit single-turn / 16bit multi-turn) with internal buffer battery• 5 PNP digital inputs and 1 analogue input -10 +10V ext. (0-5 o 4-20mA optional) • 1 relay output (NC-NO) • USB port for parametrisation • Torque, speed, position and homing control.
GEAR UNIT: with worm screw and die-cast aluminium gearcase. 26 mm centre distance. CARO bronze crown with a hardness of 120÷160 HB. The worm is made of tempered steel, with ground thread. . Seal rings in special high-temperature rubber (FKM). Lubrication with special long-lasting oil. There are 10 available gear ratios (i), from 5 to 80. Rated torque up to 9 Nm.
Version B3 - B5 (B5/S left - B5/D right).
All the models are implemented with the new “open” platform, which permits configuration with the following primary protocols: CanOpen, Ethercat, Modbus, Ethernet/IP, Profinet, Powerlink.
For full motor specifications please see motor only 'DBS' or download literature below.
N.B. To choose the right gear motor, please refer to the relevant charts for duty and maximum shaft load coefficients.
These gear motors need to be run in. Therefore, for approximately the first 30 operating hours the torque will be lower than what indicated in the data.
General Data |
|
---|---|
Nominal speed | 300 rpm |
Nominal torque | 2,7 Nm |
Input voltage dc | 24/48 Vdc |
Digital inputs | 2 pnp (24Vdc, 500kHz) , 3 pnp (24Vdc, 7kHz) |
Outputs | 1 NO 2A (42 Vdc) |
Output power | 125 W |
Rated current | 8A@24V/4.2A@48V A |
Nominal overload | 200% x 60 sec |
Motor control algorythm | Sinusoidal brushless with 12Bit single-turn / 20Bit multi-turn absolute encoder |
Nominal output frequency carrier | 4/8/12 kHz |
Electronic brake output | 24Vdc, max 0.5A |
Ambient temperature | -10 … +40°C |
Safety Features |
|
IP class | IP65 |
CE approved | Yes |
Over voltage protection | Yes |
Under voltage protection | Yes |
*Invisible Heading* |
|
---|---|
Overheat protection | Yes |
Memory error protection | Yes |
Polarity reverse protection | Yes |
Overcurrent protection | Yes |
Communication error protection | Yes |
Overload protection | Yes |
Communication |
|
Communication | USB |
Ethercat | Yes |
CanOpen | Yes |
ProfiNET | Yes |
Ethernet IP | Yes |
Modbus RTU | Yes |
PowerLink | Yes |
Ratio | 10:1 |
MOTOR: Brushless 4-pole three-phase sinusoidal motor, totally enclosed. Rotor with NdFeB magnets. Thermal cutoff. Winding Class F. Thermal cutoff. Protection IP65 in compliance with IEC/EN 60529 standards. Bearings with reduced backlash and special grease for high temperatures.
DRIVE: Power 24 and/or 48 Vdc • Magnetic absolute encoder SSI (12bit single-turn / 16bit multi-turn) with internal buffer battery• 5 PNP digital inputs and 1 analogue input -10 +10V ext. (0-5 o 4-20mA optional) • 1 relay output (NC-NO) • USB port for parametrisation • Torque, speed, position and homing control.
GEAR UNIT: with worm screw and die-cast aluminium gearcase. 26 mm centre distance. CARO bronze crown with a hardness of 120÷160 HB. The worm is made of tempered steel, with ground thread. . Seal rings in special high-temperature rubber (FKM). Lubrication with special long-lasting oil. There are 10 available gear ratios (i), from 5 to 80. Rated torque up to 9 Nm.
Version B3 - B5 (B5/S left - B5/D right).
All the models are implemented with the new “open” platform, which permits configuration with the following primary protocols: CanOpen, Ethercat, Modbus, Ethernet/IP, Profinet, Powerlink.
For full motor specifications please see motor only 'DBS' or download literature below.
N.B. To choose the right gear motor, please refer to the relevant charts for duty and maximum shaft load coefficients.
These gear motors need to be run in. Therefore, for approximately the first 30 operating hours the torque will be lower than what indicated in the data.
|
|
|
|
|
||
---|---|---|---|---|---|---|
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
Parts | Nominal speed | Nominal torque | Input voltage dc | Output power | Rated current | Ratio | Price | ||
---|---|---|---|---|---|---|---|---|---|
24/48V dc 300rpm 2.7 Nm B3 mount
Art:
MCDBS 55/50-10 B3
Copied
|
300 rpm
|
2,7 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
10:1
|
| ||
24/48V dc 300rpm 2.7 Nm B5 mount
Art:
MCDBS 55/50-10 B5
Copied
|
300 rpm
|
2,7 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
10:1
|
| ||
24/48V dc 200rpm 3.9 Nm B3 mount
Art:
MCDBS 55/50-15 B3
Copied
|
200 rpm
|
3,9 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
15:1
|
| ||
24/48V dc 200rpm 3.9 Nm B5 mount
Art:
MCDBS 55/50-15 B5
Copied
|
200 rpm
|
3,9 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
15:1
|
| ||
24/48V dc 150rpm 4.7 Nm B3 mount
Art:
MCDBS 55/50-20 B3
Copied
|
150 rpm
|
4,7 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
20:1
|
| ||
24/48V dc 150rpm 4.7 Nm B5 mount
Art:
MCDBS 55/50-20 B5
Copied
|
150 rpm
|
4,7 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
20:1
|
| ||
24/48V dc 100rpm 6.6 Nm B3 mount
Art:
MCDBS 55/50-30 B3
Copied
|
100 rpm
|
6,6 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
30:1
|
| ||
24/48V dc 100rpm 6.6 Nm B5 mount
Art:
MCDBS 55/50-30 B5
Copied
|
100 rpm
|
6,6 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
30:1
|
| ||
24/48V dc 75rpm 8.2 Nm B3 mount
Art:
MCDBS 55/50-40 B3
Copied
|
75 rpm
|
8,2 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
40:1
|
| ||
24/48V dc 75rpm 8.2 Nm B5 mount
Art:
MCDBS 55/50-40 B5
Copied
|
75 rpm
|
8,2 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
40:1
|
| ||
24/48V dc 600rpm 1.4 Nm B3 mount
Art:
MCDBS 55/50-5 B3
Copied
|
600 rpm
|
1,4 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
5:1
|
| ||
24/48V dc 600rpm 1.4 Nm B5 mount
Art:
MCDBS 55/50-5 B5
Copied
|
600 rpm
|
1,4 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
5:1
|
| ||
24/48V dc 50rpm 10 Nm B3 mount
Art:
MCDBS 55/50-60 B3
Copied
|
50 rpm
|
10 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
60:1
|
| ||
24/48V dc 50rpm 10 Nm B5 mount
Art:
MCDBS 55/50-60 B5
Copied
|
50 rpm
|
10 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
60:1
|
| ||
24/48V dc 400rpm 2 Nm B3 mount
Art:
MCDBS 55/50-7.5 B3
Copied
|
400 rpm
|
2 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
7.5:1
|
| ||
24/48V dc 400rpm 2 Nm B5 mount
Art:
MCDBS 55/50-7.5 B5
Copied
|
400 rpm
|
2 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
7.5:1
|
| ||
24/48V dc 43rpm 9 Nm B3 mount
Art:
MCDBS 55/50-70 B3
Copied
|
43 rpm
|
9 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
70:1
|
| ||
24/48V dc 43rpm 9 Nm B5 mount
Art:
MCDBS 55/50-70 B5
Copied
|
43 rpm
|
9 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
70:1
|
| ||
24/48V dc 37.5rpm 9 Nm B3 mount
Art:
MCDBS 55/50-80 B3
Copied
|
37,5 rpm
|
9 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
80:1
|
| ||
24/48V dc 37.5rpm 9 Nm B5 mount
Art:
MCDBS 55/50-80 B5
Copied
|
37,5 rpm
|
9 Nm
|
24/48 Vdc
|
125 W
|
8A@24V/4.2A@48V A
|
80:1
|
| ||
48V dc 600rpm 2.1 Nm B3 mount
Art:
MCDBS 55/100-5 B3
Copied
|
600 rpm
|
2,1 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
5:1
|
| ||
48V dc 400rpm 3.1 Nm B3 mount
Art:
MCDBS 55/100-7.5 B3
Copied
|
400 rpm
|
3,1 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
7.5:1
|
| ||
48V dc 300rpm 4 Nm B3 mount
Art:
MCDBS 55/100-10 B3
Copied
|
300 rpm
|
4 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
10:1
|
| ||
48V dc 200rpm 5.8 Nm B3 mount
Art:
MCDBS 55/100-15 B3
Copied
|
200 rpm
|
5,8 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
15:1
|
| ||
48V dc 150rpm 7.1 Nm B3 mount
Art:
MCDBS 55/100-20 B3
Copied
|
150 rpm
|
7,1 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
20:1
|
| ||
48V dc 100rpm 8 Nm B3 mount
Art:
MCDBS 55/100-30 B3
Copied
|
100 rpm
|
8 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
30:1
|
| ||
48V dc 75rpm 12 Nm B3 mount
Art:
MCDBS 55/100-40 B3
Copied
|
75 rpm
|
12 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
40:1
|
| ||
48V dc 600rpm 2.1 Nm B5 mount
Art:
MCDBS 55/100-5 B5
Copied
|
600 rpm
|
2,1 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
5:1
|
| ||
48V dc 400rpm 3.1 Nm B5 mount
Art:
MCDBS 55/100-7.5 B5
Copied
|
400 rpm
|
3,1 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
7.5:1
|
| ||
48V dc 300rpm 4 Nm B5 mount
Art:
MCDBS 55/100-10 B5
Copied
|
300 rpm
|
4 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
10:1
|
| ||
48V dc 200rpm 5.8 Nm B5 mount
Art:
MCDBS 55/100-15 B5
Copied
|
200 rpm
|
5,8 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
15:1
|
| ||
48V dc 150rpm 7.1 Nm B5 mount
Art:
MCDBS 55/100-20 B5
Copied
|
150 rpm
|
7,1 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
20:1
|
| ||
48V dc 100rpm 8 Nm B5 mount
Art:
MCDBS 55/100-30 B5
Copied
|
100 rpm
|
8 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
30:1
|
| ||
230V 75rpm 12 Nm B5 mount
Art:
MCDBS 55/100-40 B5
Copied
|
75 rpm
|
12 Nm
|
48 Vdc
|
235 W
|
6.3 A
|
40:1
|
|
Select a variant in the list
If you need any help, you can contact us in one of the following ways: